HB型链板、链斗式输送机

HB型链板、链斗式输送机概述

Product overview
    HB型链板、链斗式输送机是一种固定输送设备,该系列输送机有如下特点: 1、适应性强,本机适用于不带粘性的散状物料及粒状、块状物料的输送,尤其适用于块状较大,且具有锋利棱角,灼热的(如水泥熟料等)物料的输送,而且在输送过程中可同时完成冷却、清洗等工艺过程; 2、整机装置紧凑、安装、调试、维修方便; 3、链板、链斗结构合理、刚性好,耐冲击性强; 4、以滚动磨擦代替滑动磨擦、运行阻力低; 5、链板机适用0°~15°倾角,链斗机输送倾角最大可达45°; 6、输送距离≤30m时,可采用环链及板链作牵引件,输送距离>30m时,为防止滑动,需采用板链作牵引件。
    HB type chain plate, chain bucket conveyor is a kind of fixed conveying equipment, this series of machine has the following characteristics: 1, strong adaptability, the machine is suitable for adhesive not bulk conveying and granular, block material, especially suitable for block is larger, and has sharp edges, hot (such as cement clinker) material transport, and it can be finished at the same time in the process of conveying cooling and cleaning process, such as;2, the machine has compact device, convenient installation, commissioning, maintenance;3, chain plate, chain bucket reasonable structure, good rigidity, strong impact resistance;4, to rolling friction instead of sliding friction, low running resistance;5, chain plate for 0 ° ~ 15 ° inclination, chain bucket machine delivery up to 45 ° Angle;6, conveying distance 30 m or less, link chain and plate chain can be used for traction, conveying distance > 30 m, to prevent sliding, with the plate chain for traction.
链板输送机
链板输送机
链板输送机
 

HB型链板、链斗式输送机外形结构

Structures
    1、链板机板沿高一般为80~120mm,视输送物料及输送量在设计时可适当变动,其物料是连续在链板上存放,为防止其过多漏料,其上倾角度一般不大于15°,其外型结构见下图。
    2、链斗机的物料是存放在单链斗里进行输送,其在输送过程中,依靠重力及滚轮作用,链斗总处于水平状态,故其可用于较大倾角输送物料过程,其最大上倾角可达到45°,共外型结构见下图。

1, chain plate plate along the high average for 80-120 mm, depending on the conveying material and throughput can be appropriate when the design change, its material is continuous on the chain plate storage, to prevent the excessive leakage material, are rarely more than 15 ° inclination angle, its appearance structure below.
2, chain conveyor for conveying materials is stored in a single bucket, its in the process of conveying, rely on gravity and roller, bucket chain always is in a state level, so the process of conveying material can be used in large dip Angle, the maximum Angle can reach 45 °, exterior structure below.
链斗输送机
链斗输送机
链斗输送机
链斗输送机

HB链板输送机产品特点:

1.输送效率高 物料在链式输送机的机槽内呈整体流动,因而较小的机槽空间可以输送大量的物料,设备的外形尺寸也相应较小。
2.能耗低 该机借助物料内磨擦力进行输送,输送链与机壳无磨擦运动。在同等输送量和较长输送距离的条件下,该机的电力消耗比螺旋输送机低40%左右。
3.故障率低 输送链上的滚子在导轨上滚动,输送链与机壳无磨擦。链条采用合金钢热处理加工制成,其正常使用寿命3年左右,运行中故障率低。除头尾轴承外,输送机中无润滑点。

Features
1. High transmission efficiency material in chain conveyor in slot machine shows the overall flow, thus the smaller machine groove space can transport a large number of materials, size and the shape of the device smaller accordingly.
2. The consumption of low The machine with the aid of material in friction in transmission, conveyor chain and chassis no friction movement.Under the same throughput and long conveying distance, under the condition of the machine electricity consumption of about 40% lower than the screw conveyor.
3. The failure rate is low roller rolling on the guide rail, conveyor chain conveyor chain and chassis no friction.Made of chain using alloy steel heat treatment process and the normal service life of 3 years or so, in the operation of the low failure rate.Besides end bearing, no lubrication point in the conveyor.
链斗输送机
链斗输送机

HB链板式输送机结构示意图

Pictures of structures
外形图

 

HB型链板、链斗式输送机注意事项

Notes
 1 、链斗机、链板机主要用于输送磨损强,温度高的物料,用户订货时需注明型号,两轮中心距,倾斜角度,最大输送量等工艺参数。
 2、动力装置在链斗(板)机头部、左、右装可根据用户要求变动。
 3、输送速度以8~10m/min为宜,太低影响输送量,太高噪音大,磨损增大。且HB800、HB1000适宜输送堆密度较小的物料。

1, chain conveyor, chain plate is mainly used for conveying strong abrasion, high temperature materials, when you place an order to indicate the type, two rounds of center distance, Angle and maximum throughput of the process parameters.
2, power plant in the bucket (plate), left, right nose department can change according to user requirements.
3, transmission speed with 8 ~ 10 m/min advisable, low influence throughput, high noise, wear and tear.And HB800, HB1000 is suitable for conveying materials bulk density smaller.
订货须知: 1、倾角输送时,倾角在5°左右,输送量会降低3%,倾角左右在10°左右,输送量会降低12%,倾角在15°左右,输送量会降低20%。
2、输送物料温度用普材不大于200℃,如链板及牵引链用耐高温材料(如高铬高镍钢)制造,物料温度可达400℃。
3、最大物料粒度不超过物料总量的15%,当物料块度较大且较多时,会影响输送量。
4、如用在清洗工艺中,应有清洗水槽(液体槽)把水收集。

Ordering instruction

1, inclination conveying, at about 5 ° inclination, throughput decreases 3%, about dip in 10 ° or so, throughput decreases 12%, the Angle of about 15 °, the throughput will be reduced by 20%.
2, conveying material with grade wood is not greater than 200 ℃ temperature, such as chain plate and traction chain with high temperature resistant material, such as high chromium and high nickel steel manufacturing, material temperature can reach 400 ℃.
3, maximum particle size does not exceed 15% of the total material, when material are too many and more, can affect throughput.
4,In the cleaning process, should be clean water tank (liquid tank) to collect water.
上一篇:FU型链式输送机 下一篇:U型螺旋输送机
更多输送机械设备产品
  • 官方微信